koa speer electronics, inc. ss-218 r5 aha 5/25/07 bolivar drive p.o. box 547 bradford, pa 16701 usa 814-362-5536 fax 814-362-8883 www.koaspeer.com specifications given herein may be changed at any time without prior notice. please confirm technical specifications before you order and/or use. page 1 of 6 current detecting chip resistors type tsl1 1. scope of application this specification applies to current detecting chip resistors (tsl) manufactured by koa corporation. 2. type designation the type designation shall be in the following form: certified certified size tolerance nominal resistance 1 watt d: 0.5% f: 1% j: 5% ?%: 2 significant figures + 1 multiplier ??indicates decimal on value <10 ?%: 3 significant figures + 1 multiplier ??indicates decimal on value <100 all values less than 0.1 (100m ) are expressed in m with ?? as decimal example: 20m , 1% = 20l0 1 f 20l0 packaging te: 7" embossed plastic (tsl - 3,000 pieces/reel) te termination material t: sn (other termination styles may be available, please contact factory for options) t tsl type absolute maximum working voltage resistance tolerance e-24* resistance range part designation absolute maximum overload voltage operating temperature range power rating t.c.r. (ppm/?) max. tsl1 1w -55? to +180? ?80: r=<13m ?00: r=>15m p r p r 10m - 100m (f: ?%) (j: ?%) 5m - 100m * 3m, 4m, 5m, 6m, 7m, 8m, 9m resistance values also available (d: ?.5%) 3. rating ss-218 r5 5/25/07 5:25 pm page 1
koa speer electronics, inc. ss-218 r5 bolivar drive p.o. box 547 bradford, pa 16701 usa 814-362-5536 fax 814-362-8883 www.koaspeer.com specifications given herein may be changed at any time without prior notice. please confirm technical specifications before you order and/or use. page 2 of 6 1 2 3 resistive element flameproof molded epoxy case with ul94v-0 flammability rating end termination with tin/lead solder plating 1 2 3 4-2 structure 4. dimensions and structure 4-1 dimensions w t l a b c c molded resin resistive element electrode .122?008 (3.1?.2) .039?008 (1.0?.2) .248?012 (6.3?.3) .094?008 (2.4?.2) .047?012 (1.2?.3) tsl1 c b a t w l dimensions inches (mm) .028?008 (0.7?.2) size code 5-2 voltage rating resistors shall have a rated direct-current (dc) continuous working voltage or approximate sine- wave root-mean-square (rms) alternating-current (ac) continuous working voltage at commercial-line frequency and waveform corresponding to the power rating, as determined from the following formula: where: e = rated voltage (v) e = p x r p = rated power (w) r = nominal resistance ( ) 5. rating derating curve surface temperature rise % rated power 100 80 60 40 20 -60 -40 0 40 60 80 100 180 70 20 ambient temperature ( c) 0 120 -20 140 160 -55 temperature rise ( c) 150 100 50 50 100 % rated power tsl1 (1) tsl1 (2) 0 0 25 75 2 1 25 75 125 5-1 rating sl3 for temperature in excess of 110?, the load shall be derated in accordance with the following figure. 100 80 60 40 20 0 -55 0 110 125 180 ambient temperature ( c) ss-218 r5 5/25/07 5:25 pm page 2
koa speer electronics, inc. ss-218 r5 bolivar drive p.o. box 547 bradford, pa 16701 usa 814-362-5536 fax 814-362-8883 www.koaspeer.com specifications given herein may be changed at any time without prior notice. please confirm technical specifications before you order and/or use. page 3 of 6 6. characteristics 6.1 electrical characteristics no. requirement 1 2 5 6 3 4 resistance insulation withstanding voltage below ?.5% no short, burning and arc t.c.r. short time overload intermittent overload within tolerance above 10 4 m r < 13 m 180 ppm/? r 15 m 100 ppm/? below ?.0% below ?.0% jis c 5202 5.1 measuring voltage a 25? jis c 5202 5.6 surface center to termination d.c. 500v jis c 5202 5.7 a.c. 500v 60 sec. jis c 5202 5.2 +25? / +125? rp x 2.5 5 sec. jis c 5202 5.8 rv x 5.0 1 sec. on / 25 sec. off 1,000 cycles characteristics test method ss-218 r5 5/25/07 5:25 pm page 3
koa speer electronics, inc. ss-218 r5 bolivar drive p.o. box 547 bradford, pa 16701 usa 814-362-5536 fax 814-362-8883 www.koaspeer.com specifications given herein may be changed at any time without prior notice. please confirm technical specifications before you order and/or use. page 4 of 6 6.2 mechanical no. requirement 1 resistance to soldering heat below ?.0% 6.10 260? ?? 5 ?.5 sec. 3 vibration below ?.5% 6.3 condition a each direction / 2 hrs. 4 resistance to solvent no visual and mechanical damage 6.9 characteristics test method (jis c 5202) 2 solderability more than 95% of the surface of the termination must be covered with new solder 6.11 235? ?? 2 ?.5 sec. 6.3 environmental characteristics no. requirement 1 damp heat below ?.0% no visual damage 7.9 40? ?? 90 ~ 95% rh 1,000 hrs. 3 temperature cycling below ?.0% no mechanical damage 7.4 -55? / +155? each 30 minutes 100 cycles 4 flammability incombustibles 7.2 3.1 in flame / out flame 15 sec. / 15 sec. 5 cycles characteristics test method (jis c 5202) 2 endurance (rated load) below ?.0% no visual damage 7.10 70? ?? 1,000 hrs. ss-218 r5 5/25/07 5:25 pm page 4
koa speer electronics, inc. ss-218 r5 bolivar drive p.o. box 547 bradford, pa 16701 usa 814-362-5536 fax 814-362-8883 www.koaspeer.com specifications given herein may be changed at any time without prior notice. please confirm technical specifications before you order and/or use. page 5 of 6 a 1 b 1 cdefghj tsl .134 .260 .472 .216 .069 .157 .079 .157 .059 (3.4 0.1) (6.6 0.1) (12.0 0.2) (5.5 0.1) (1.75 0.1) (4.0 0.1) (2.0 0.1) (4.0 0.1) (1.5 0.1 ) 0.0 7. taping 7-1 dimensions of carrier tape t 1 k 1 j q f g h c d e b 1 a 1 dimensions in inches (mm) k 1 qt 1 tsl .051 .059 .010 (1.3 0.1) (1.5 0.1 ) (0.25 0.05) 0.0 7-2 taped configuration dimensions in inches (mm) end tape (empty) (empty) leader tape 5.90 (150) min. 1.57 (40) min. 3.15 (80) min. (top tape) ss-218 r5 5/25/07 5:25 pm page 5
koa speer electronics, inc. ss-218 r5 bolivar drive p.o. box 547 bradford, pa 16701 usa 814-362-5536 fax 814-362-8883 www.koaspeer.com specifications given herein may be changed at any time without prior notice. please confirm technical specifications before you order and/or use. page 6 of 6 8-1 body and marking 8. recommended land pattern g e f land solder resist dimensions in inches (mm) ef g .181 .315 .118 tsl1 (4.6) (8.0) (3.0) body color black marking color white marking items resistance value and tolerance 7-3 reel dimensions qty/ ? ? ? ? e w 1 w 2 reel tsl 7.08 2.36 .511 .826 .079 .511 .606 (180 0.0 ) (60 1.0 ) (13.0 0.2) (21.0 0.8) (2.0 0.2) (13.0 0.3) (15.4 1.0) 3,000 3.0 0.0 dimensions in inches (mm) w1 ? ? ? ? e w2 ss-218 r5 5/25/07 5:25 pm page 6
|
